Source: receiver from 100 L, 8 bar
01
Connect to compressor
The Turbo Cleaner pneumatic gun connects to a compressed air source via a standard quick-release coupling.
Source: receiver from 100 L, 8 barAir filter blow-cleaning system
Dust stays outside
Turbo Cleaner — a tool for controlled blow-cleaning of cylindrical air filters on engines of equipment that constantly works in dust. The rotor is matched to the filter's inner diameter and distributes compressed air across the entire inner surface.
Scroll down
Operating conditions
The filter takes on all the dust of the working day
Dusty environment / maintenanceIn the field, on construction sites and in quarries, the air filter clogs faster than you would like. It must be serviced regularly — sometimes several times per shift.
Blow-cleaning with a regular tube works, but the result depends on how the operator directs the jet: at what angle, for how long and along which path. From one time to the next — it varies.
High dust levels
Harvesting, dirt roads and dusty yards continuously load the filter.
Regular maintenance
Clean intake air is needed constantly, not once a season.
Skill dependency
Manual blow-cleaning gives different results with different operators and on different shifts.
Downtime at the wrong time
During the season, every equipment stop is especially unwelcome.
How it works
Compressed air — across the entire inner surface of the filter
Three steps, a repeatable process. The operator follows the instructions and watches for when dust stops exiting the filter.
02
Rotor — inside the filter
The rotor is matched to the filter's inner diameter and inserted into the cylindrical filter element. The cone restrictor «Pyramid» covers the inlet and keeps dust out of the clean cavity.
Rotor for Ø 80–250 mm
03
Blow-cleaning and control
The airflow spins the rotor and the jet blows dust out of the pleats. A linear motion covers the entire surface — until dust exit stops, approximately three minutes.
≈ 3 minutes per elementTechnical data
Parameters, not marketing adjectives
80–250mm
Filter inner diameter
Approximate range of compatible cylindrical elements.
4pcs
Interchangeable rotors
Matched to different filter inner diameters.
from 100L
Receiver volume
Recommended volume to maintain flow without pressure drops.
8bar
Compressor pressure
Recommended pressure that can be maintained steadily.
up to 4bar
Rotor jet at 8 bar inlet
At 10 bar inlet — up to 5 bar at rotor outlet.
≈ 3min
Blow-cleaning one element
Guideline. Exact time — until visible dust exit stops.
≈ 1min
Device assembly
Stated preparation time before use.
1year
Warranty
Stated manufacturer warranty.
Compatibility check
Will Turbo Cleaner fit your equipment
A short check against basic parameters. Nothing is sent — the calculation runs in your browser. This is a preliminary guide, not a replacement for the filter manufacturer's instructions.
Result
Answer four questions — we will show a preliminary compatibility estimate. Answered: 0 of 4.
Where it is used
Equipment that cannot afford downtime
Agriculture
- Combines and tractors during harvest
- Filter service right in the field
Truck fleet
- Trucks on dirt roads
- Loaders and warehouse equipment
Road construction
- Road construction equipment
- Working in constant dust
Quarries and dusty yards
- Quarry equipment
- Dusty yards and open pits
What's in the kit
Assembles in about a minute
Assembled unit≈ 1 min assembly
Interchangeable rotors
4 pcsFor different inner diameters of cylindrical filters.
Cone restrictor «Pyramid»
Covers the inlet and keeps dust out of the clean filter cavity.
Pneumatic gun
Delivers compressed air, connects to a compressor.
Extension rod
Connects the gun and working head, sets the reach length.
Manual and packaging
Assembly and operation guide, transport packaging.
Photos show the actual kit contents. Composition and appearance may vary by manufacturer.
Process comparison
Regular tube and Turbo Cleaner
The work process is compared, not cleaning effectiveness.
Regular blow-cleaning tube
- Operator manually directs a localised jet
- Result depends on trajectory and processing time
- Filter surface must be covered sequentially
Turbo Cleaner
- Rotor matched to filter inner diameter
- Work process runs inside the cylindrical element
- Jet pressure limited by design within stated parameters
- Completion guide — visible dust exit stops and instructions
Video
What it looks like in operation
Real footage of the device at work. Captions describe what happens in the video; names and farms are not listed — we do not provide unverified attribution.
Questions & answers
The essentials
Ready to try
Clean filter. Working equipment.
- Four interchangeable rotors
- Filters Ø 80–250 mm
- Compressor from 100 L · 8 bar
- 1 year warranty
Whether blow-cleaning and reuse of the filter element is permitted is determined by the filter and equipment manufacturer. Check the operating manual before use. Damaged, wet, oil-contaminated and non-cleanable elements must be replaced.
